Search

The Online Encyclopedia and Dictionary

 
     
 

Encyclopedia

Dictionary

Quotes

 

Category 5 cable

(Redirected from Cat-5)


Category 5 cable, commonly known as Cat 5, is an unshielded twisted pair type cable designed for high signal integrity. The actual standard defines specific electrical properties of the wire, but it is most commonly known as being rated for its Ethernet capability of 100 Mbit/s. Its specific standard designation is EIA/TIA-568. Cat 5 cable typically has three twists per inch of each twisted pair of 24 gauge copper wires within the cable. Another important characteristic is that the wires are insulated with a plastic (FEP) that has low dispersion, that is, the dielectric constant of the plastic does not depend greatly on frequency. Special attention also has to be paid to minimizing impedance mismatches at connection points.

It is often used in structured cabling for computer networks such as fast Ethernet, although it is often used to carry many other signals such as basic voice services, token ring, and ATM (at up to 155 Mbits/s, over short distances).

The other well known flavour of this type of cable is the 10 Mbit/s Category 3 cable. Less well known is the 20 Mbit/s Cat 4. Cat 4 offered only a small advance in speed over Cat3, and was generally ignored in favour of Cat 5. Cat 1 and Cat 2 are 1 Mbit/s systems for voice and low-speed data.

Patch leads created from Cat 5 are often terminated with RJ-45 electrical connectors. Normal Cat 5 cables are wired "straight through" and connect a computer to a hub or switch. In other words, pin 1 is connected to pin 1, pin 2 to pin 2, etc. The RJ-45 pinout for a Cat 5 cable can either be TIA-568A or TIA-568B. TIA-568A is used by some phone systems and Token Ring. Most everything else, such as the Ethernet standards 10BASE-T and 100BASE-TX, use TIA-568B.

In Ethernet, "crossover" Cat-5 cables are cables in which pairs two and three are reversed. (For 100BASE-T4 a more complex connection layout is needed.) These are most often used to connect two PC's NICs directly (with no intervening hub). They can also be used to connect two hubs or switches together. However most hubs and switches either have an uplink port , a button to change a port to uplink or one or more ports with autosense (most modern switches now have autosense on every port). These features eliminate the need for crossover cables when connecting them. See the Crossover cable and TIA-568B articles for pinout diagrams.

Cat 5e cable is an enhanced version of Cat 5 for use with 1000 Base-T networks, or for long-distance 100 Base-T links (350 m, compared with 100 m for Cat5). It must meet the EIA/TIA 568A-5 specification.

Cat 6 cable is defined by the ANSI TIA/EIA 568B-2.1. It is suitable for 1000 Base-T (gigabit) Ethernet up to 100 m.

Cat 7 cable, with four individually-shielded pairs (ScTP) inside an overall shield, has been proposed but is not in common use. It is designed for transmission frequencies up to 600MHz, which should enable it to carry 10-Gigabit Ethernet (10GBaseT ), but requires a redesigned RJ-45 connector (called a GG45 ) to achieve this speed. Also in development are non RJ-45 backward compatible standards such as (Tera) from siemons, Tera promises transmission frequencies of up to 1200Mhz. 10GBaseT networks are not yet widely available, and may not be able to compete with fibre optic networks.

Source: Mysticom Press Release, Nov. 2003

See also

External links

Last updated: 08-17-2005 17:10:43
The contents of this article are licensed from Wikipedia.org under the GNU Free Documentation License. How to see transparent copy